Real-World Interfacing
In this lab you will be introduced to the programming language C, and the PIC16F873, a popular and very widely used m-controller (read micro-controller). m-controllers find use in devices that needs some intelligence but not a huge amount of processing power (eg, fancy graphical interfaces, massive computing needs). You can find these devices in cars (engine control, anti-lock brakes...), in appliances, etc... There are many ways to program these devices, but you will be using C to program the PIC to perform some fairly simple tasks. C is often used with m-controllers because of its small size, high speed, and the access it allows to the real-world. This week you will get a short introduction to C as well as a brief look at some of the capabilities of the PIC.
A good resource for help with the PIC programmed with the CCS C-compiler is given at http://www.ccsinfo.com/forum/.
The PIC microcontroller comes in a wide range of variants. You can check them out in data books that are in the lab, or at the MicroChip web site. A m-controller is distinguished from a m-processor in that it has many capabilities useful for real-world interfacing built into the chip. The PIC has a RISC-based Harvard architecture with separate memory for data and program. The one we will be using is the PIC16F873 (link to data sheet) It has an on-board RAM (Random Access Memory), EPROM (Erasable Programmable Read Only Memory), an oscillator, a couple of timers, and several Input/Output (I/O) pins, serial ports and 8 channel A/D convertor (if you don’t know what all of those things are don’t worry; suffice it to say there can be an impressive array of peripherals built into the chip). However, the m-controller is less computationally capable than most m-processors due to the fact that they are used for simple control applications rather than spreadsheets and elaborate calculations. As an example, the PIC16F873 has 4096 words of memory for program, and only 192 bytes of RAM, and can only operate with clocks up to 20 MHz on 8 bits of data (compared to megabytes of RAM, Speeds of a GHZ or more and 32 or even 64 bits of data for many desktop systems). It also has no facilities for floating point numbers... A pinout of the PIC16F873 is shown below.
There are several pins that are used to power the device. Many of the other pins have multiple uses depending on how the device is programmed.
This week, and the next, you will be using a m-controller in the lab. These laboratories will serve as a brief introduction to the processor and to programming in C.
Getting started with C.
A simple C program
A very simple C program is shown below./*simple.c -- sets a pin low, then high*/#INCLUDE <16f873.h> #USE DELAY (CLOCK=4000000)void main() { output_low(pin_C1); output_high(pin_C1); }This program has many common features of C programs. The first line is a comment that is ignored by the compiler. It is simply there to document what the program code does. A comment is anything that occurs between a "/*" and the subsequent "*/". The next line is a "directive". All directives begin with a "#" and are used to convey information to the compiler. The directive in this program tells the compiler to include a header file ("16F873.h") which is necessary when using the microcontroller’s input and output capabilities. The next two directives tell it how to configure the device, and how fast it goes. The next line tells the compiler that this is the "main" program, and that everything between the opening brace, {, and the matching closing brace, , constitutes the main program. The main program itself is only two lines. The first line (not a comment) is a call to the "output_low" function, which sets output pin pin_C1 low, and a call to output_high, which sets it high. . Note that after every program statement there is a semi-colon. This is very important.
Variables
Almost all programs will use variables which are simply units of information stored in the computers memory. The standard C language has a wide variety of variable types available, however the dialect we will be using is more restricted. The version of C that we will be using has a quite unstandard set of variable types that are suited to its architecture.
Type Specifier Size Range unsigned 8 bit unsigned 0 to 255 unsigned int int char int8 long 16 bit unsigned 0 to 65535 long int int16 signed 8 bit signed -128 to 127 signed int signed int8 signed long 16 bit signed -32768
to 32767signed int8 int32 32 bit unsigned 4*109 signed int32 32 bit signed ±2*109 float 32 bit floating point ±0.5*2-128 to 1-(2-15)*2128 short one bit 0 to 1 short int int1
The program below shows how variables are used.
#INCLUDE <16f873.h> #USE DELAY (CLOCK=4000000)void main() { char i, j, k; /* declare characters */i=2; j=3; k=i+j; }
Again we have a fairly simple program that shows many different features of C. Note the semicolon after every program statement. We declare 3 char’s, "i", "j" and "k". A char is simply an 8 bit variable. You should use chars whenever possible because the PIC is designed to work on data 8 bits at a time.
Numerical manipulations
C has a variety of built in operations for performing math. These are listed below along with an example where a=0x03, and b=0x11:
Logical Expressions
In addition ot manipulating numbers, C is also capable of handling logical expressions. When using these expressions TRUE is taken to be anything that is not zero, and FALSE is always equal to zero. Again, a=0x03, and b=0x11:Binary operators (two operands)
Symbol
a=0x03 b=0x11Binary Operators Greater than > a>b FALSE < a TRUE == a==b FALSE >= a>=b FALSE <= a<=b TRUE != a!=b TRUE && a&&b TRUE || a||b TRUE ! !a FALSE
Manipulating addresses (somewhat advanced topic, may be skipped)
There are two operators used for manipulating addresses and you have already been briefly introduced to one of them, the indirection operator, *. The other one is the address operator &. If you have an address k, the value stored at that address is *k. If you have a variable j, the address of the variable is given by &j. Therefore it is obvious that *(&j)=j.
I/O (Input/Output) Ports
It is possible with with a PIC to interact with the real world. This is done thourgh the use of I/O ports. The PIC16F873 has 3 I/O ports, labeled "a", "b" and "c". We will use Port A for analog input, though it has other uses. Ports B and C will be used for digital I/O. On the schematic the pins are labeled RB0 through RB7, but the compiler refers to them as pin_B0 through pin_B7. Likewise for port C. The pins can be used for either input or output.Your circuit has the pushbutton switch connected to RB0, and the LED's to pins RC0 through RC7.Digital OutputThere are several functions that are used for output from the PIC. A full listing is in the PCB manual. Four commonly used functions are:
- Output_high(pin)
Sets the specified pin to a logic 1 (about 5 volts).- Output_low(pin)
Sets the specified pin to a logic 0 (about 0 volts)- Output_float(pin)
Sets the specified pin to a high-impedance (or tri-state) state. In this state it is as if the pin has no connections to the chip. Current can neither go in or out of the pin.- Output_bit(pin, value)
This function sets the specified pin to the specified value (which must be 0 or 1).Digital InputThere is only one input function you will need for the PIC.
- Input(pin)
Reads the value on a specified pin. The value is returned in a short int. A proper use of the function would be something like:
while( !input(pin_B0)) { ... }
which would repeat the commands in the braces as long as RB0 was low.
"High level" I/O
If the PIC is connected to the PIC C development software via the debugger it is possible to do some higher level input and output. These interactions take place via the debugger's "Monitor" window.You specify that IO is to take place through the debugger by properly defining serial connections (usually in your codes header file):#use rs232(DEBUGGER)You can then print to the monitor window by using "putc()" which sends a character to the monitor window, "puts()" which sends a string, or "printf()" which sends a formatted string. The "printf()" command is most useful, but also the most complicated (and takes the most memory).The syntax ofprintfis the following:printf(format-string, [arg_1] , ... , [arg_N] )This is best illustrated by some examples.Printing Examples
Example 1: Printing a message. The following statement prints a text string to the screen.printf("Hello, world!\n");In this example, the format string is simply printed to the screen.The characterExample 2: Printing a number. The following statement prints the value of the integer variable\nat the end of the string signifies end-of-line. When an end-of-line character is printed, the LCD screen will be cleared when a subsequent character is printed. Thus, mostprintfstatements are terminated by a\n.xwith a brief message.printf("Value is %d\n", x);The special formExample 3: Printing a character. The following statement prints the ascii equivalent of the integer variable%dis used to format the printing of an integer in decimal format.xwith a brief message. Here is an ascii table.printf("Value is %d, ascii = %c\n", x, x);Example 4: Printing a number in binary. The following statement prints the value of the integer variablexas a binary number.printf("Value is %b\n", x);The special form%bis used to format the printing of an integer in binary format. Only the low byte of the number is printed.
Example 5: Printing a floating point number. The following statement prints the value of the floating point variablenas a floating point number.printf("Value is %f\n", n);The special form%fis used to format the printing of floating point number.
Example 6: Printing two numbers in hexadecimal format.printf("A=%x B=%x\n", a, b);The form%xformats an integer to print in hexadecimal.Formatting Command Summary
%d- Type:
intDescription: decimal number%x- Type:
intDescription: hexadecimal number%b- Type:
intDescription: low byte as binary number%c- Type:
intDescription: low byte as ASCII character%f- Type:
floatDescription: floating point number%s- Type:
char arrayDescription: char array (string)
Format Command Data Type Description %dint decimal number %xint hexadecimal number %bint low byte as binary number %cint low byte as ASCII character %ffloat floating point number %schar array char array (string) Your circuit has the pushbutton switch connected to RB0, and the LED's to pins RC0 through RC7.InputUnfortunately, you can only receive input from the keyboard one character at a time using the getc() command. Be aware:As an example, the following code gets the ascii value in k, converts to a number, and prints the number.
- getc() returns the ascii equivalent of the character entered into the keyboard.
- the keyboard I/O is implemented in software on the PIC. That means, it won't receive input from the keyboard unless it is explicitly looking for it. Therefore, your program must stop in order to look for input from the keyboard. (Hardware communications could receive a character in the background, without requiring software support).
k=getc(); %Get ascii value of keyboard input.
k=k-'0'; %Subtract value of '0' to convert to number.
printf(" ... k=%d\n",k); %print the number.
Control of Flow
What you have learned up to this point has been useful but is of limited utility because it does not allow for decision making capabilities by the computer. C has a variety of mechanisms to control the flow of a program. These are listed below:
The if...then constructif (logical expression) {
...statements...
}If the logical expression is true then evaluate the statements between the braces. The following code sets RC1 if a is even.if ((a%2) == 0) {
Output_high(pin_C1);
}The if...then...else constructif (logical expression) {
...if statements...
}
else {
...else statements...
}If the logical expression is true then evaluate the "if" statements between the braces, otherwise execute the "else" statements. The following code decides if a number if is even or odd.if ((a%2) == 0) {
Output_high(pin_C1);
}
else {
Output_low(pin_C1);
}while (logical expression) { ...statements... }While the logical expression is true, the statments (of which there is an arbitrary number) between the braces is executed. The following code cycles through the even numbers from 0 to 9 (the variables must have been declared elsewhere in the program).a=0; while (a<10) a="a+2;">
The for loopfor (initial condition; logical expression; change loop counter variable) {
...statements...
}Set the initial condition, then while the logical expression is true execute the statement between the braces while changing the loop counter as specified once at the end of each loop. This code segment is functionally equivalent to the one for the "while" loop.for (a=0; a<10; a=a+2) {
...statements...
}
The case...switch constructCase..switch is used in place of a series of "if...else" clauses when a variable can take on several values. The "default" clause at the bottom takes care of any cases not covered explicitly.
switch (variable) {
case val1: ...statements 1...
break;case val2: ...statements 2...
break;case val3: ...statements 3...
break;default: ...statements default...
break;}
Functions
Often a series of instruction must be repeated over and over again. Instead of repeating the same operations repetitively it is useful to use a function that performs the repetitive operations. For instance to set a value on RC1 and then read from RB0 and set RC0 to that value, and returning the value of RB0 you might use a function called "RB0toRC0". (Note: this program isn't meant to be particularly useful, but to introduce the syntax for function declaration, and use).
/*simpleFunc.c -- to demonstrate function calls*/
#INCLUDE <16f873.h> #USE DELAY (CLOCK=4000000)short int RB0toRC0(RC1val) short int RC1val; { Output_bit(pin_C1, RC1val); /*Set RC1 to the specified value*/ if (input(pin_B0)) { /*Read RB0*/ Output_high(pin_C0); /*If RB0 is high, RC0 set high*/ } else { Output_low(pin_C0); /*else set RC0 low*/ } return(input(pin_B0)); /*Return RB0*/ }void main() { short int b; b=RB0toRC0(1); b=RB0toRC0(0); }
This program introduces some new constructs. The most obvious is the function "RB0toRC0" which is at the top. The first line of the function declares that the function returns a short int, and has one argument. The type of the argument is given before the function's opening brace. The body of the function (between the braces) outputs a value to RC1, and reads from RB0 and echos to RC1. The last line tells that compiler to return the value of RB0 to the calling function.The function is called in the main program with different arguments. The first call would set RC1 high, and return the current value of RB0 to the variable "b". The next line would set RC1 low, and return the value of RB0 to the variable "b".
Wrapping up
You should now know enough to do some fairly simple things with the microcontroller. This has been a very brief introduction to C and did not even begin to touch the richness available with the language. If you would like to know more look in the manuals in the lab, or some of the books in the library.
Other Info
If you want to work with the LCD on the PICDEM2 Plus board, you will find that documentation ranges from poor to nonexistent. Some working code is here.Code for the PICDEMlcd board is equally poor/nonexistent/incorrect. Some working code is here.
Read more: http://cmagical.blogspot.com/2010/01/introduction-to-c-and-pic.html#ixzz0y17VD9E0
Under Creative Commons License: Attribution Non-Commercial No Derivatives
No comments:
Post a Comment